提交詢價信息 |
發布緊急求購 |
價格:電議
所在地:河北 邢臺市
型號:
更新時間:2018-08-15
瀏覽次數:769
公司地址:河北省邢臺市橋東區泉南東大街唐寧10號B座1707
張經理(先生) 銷售經理
1、武JX1252EMF5000系列一體式電磁流量計JX1268哪家專業
2、武JX1252EMF5000系列一體式電磁流量計JX1268哪家專業圖片
![]() |
![]() |
型號:JX1252 | 型號:JX1268EMF5000系列一體式電磁流量計 |
3、武JX1252EMF5000系列一體式電磁流量計JX1268哪家專業內容
1 概述
工作原理
電流量計測量原理是基于法拉第電磁感應定律。流量計的測量管是一內襯緣材料的非導磁合金短管。兩只電沿管徑方向穿通管壁固定在測量管上。其電頭與襯里內表面基本齊平。勵磁線圈由雙方波脈沖勵磁時,將在與測量管軸線垂直的方向上產生一磁通量密度為B的工作磁場。此時,如果具有一定電導率的流體流經測量管。將切割磁力線感應出電動勢E。電動勢E正比于磁通量密度B,測量管內徑d與平均流速v的乘積。電動勢E(流量信號)由電檢出并通過電纜送至轉換器。轉化器將流量信號放大處理后,可顯示流體流量,并能輸出脈沖,模擬電流等信號,用E=KBdv
式中:E---------------為電間的信號電壓(v)
B-----------------磁通密度(T)
d------------------測量管內徑(m)
v------------------平均流速(m/s)
式中k, d為常數,由于勵磁電流是恒流的,故B也是常數,則由E=KBdv可知,體積流量Q與信號電壓E-成正比,即流速感應的信號電壓E與體積Q成線性關系。因此,只要測量出E就可確定流量Q,這是電磁流量計的基本工作原理。
由E=KBdv可知,被測流量體介質的溫度、密度、壓力、電導率、液固兩兩相流體介質的液固成分比等參數不會影響測量結果。至于流動狀態只要符合軸對稱流動(如層流或者動及阻流部件,因此幾乎沒有壓力損失,并且有分高的可靠性。
污水泥漿電磁流量計 應用領域
由于電磁流量計有其獨特的優點,因此被廣泛用于化工化纖、食品、造紙、制糖、礦冶、給排水、環保、水利水工、鋼鐵、石油、制藥等工業領域中,用來測量各種酸、堿、鹽溶液、泥漿、礦漿、紙漿、煤水漿、玉米漿、纖維漿、糧漿、石灰、污水、原水、給排水、鹽水、雙氧水、啤酒、麥汁、各種飲料、黑液、綠液等導電液體介質的體積流量
2污水泥漿電磁流量計主要技術參數
●公稱通徑系列DN(mm) 管道式四襯里: 10,15,20,25,32,40,50,65,80,100,125 150,200,250,300,350,400.450,500,600 管道式橡膠襯里: 40,50,65,80,100,125,150,200,300 350,400,500,600,800,1000,1200 注:特殊規格可以定制 ● 流動方向 正,反,凈流量, 量程比:150:1 重復性誤差:測量值的&plun;0.1% ● 精度等級:管道式:0.5級,1.0級 ● 被測介質溫度: 普通橡膠襯里:-20~+60℃ 高溫橡膠襯里:-20~+90℃ 聚四乙烯襯里:-30~+100℃ 高溫型乙烯襯里:-30~+180℃ ● 額定工作壓力: 管道式:DN10—DN65:≤2.5Mpa, DN80—DN150:≤1.6Mpa, DN200—DN1200:≤1.0Mpa ● 流量測量范圍: 流量測量范圍對流速度范圍是0.3—15m/s
|
● 電導率范圍: 被測流體電導率≥5μs/cm 大多數以水為成份的介質,其導電率在200-800μs/cm范圍內,均可選用電磁流量; ● 輸出電流及負載電阻: 4~20mA全隔離負載電阻<750歐姆脈沖頻率0-1KHZ光電隔離OCT外接電源≤35V 導通時 集電電流為25mA ● 電材料: 含鉬不銹剛、鈦(Ti)、鉭(Ta)、哈氏合金(H)、鉑(Pt)或其他特殊電材料 ● 防護等級: 潛水型: IP68,其他型 IP65 ● 供電電源: 85~265V, 45~63HZ ● 直管段長度: 管道式:上游≥5DN,下游≥2DN ● 連接方式: 流量計與配管之間均采用法蘭連接,法蘭連接尺寸應符合GB9119-88的規定。 ● 防暴標志:mdllBT4 ● 環境溫度: -25℃~+60℃ ● 相對溫度:5%~95% ● 消耗總功率:小于20W
|
污水泥漿電磁流量計常見介質電導率表
液體 |
電導率(μs/cm) |
液體 |
電導率(μs/cm) |
各種酸 |
10*104-801*104 |
啤酒 |
600-800 |
堿液 |
8*104-30*104 |
麥芽汁 |
500-1000 |
蒸餾水 |
0.01-5 |
牛奶 |
200-300 |
水及飲料 |
200-800 |
水果醬 |
400-1000 |
3電磁流量計選型
LT-LDE—□□—□ □ □ □ □ □ —□
通徑 組合 電 0—無輸出 襯里 0—無就地顯示 0—無通訊 0—無接地環 上限流量
(mm) S— 一體型 M—MO2Ti 1— 4—20mA/0—1KHZ X—橡膠 1—就地顯示 1——RS485 1—有接地環 m3/h
L— 分體型 T—TiI(鈦) 2—4—20Ma F—四 2——RS232
D—Ta(鉭) P—聚乙烯 3——MOdbus
H—哈氏合金 4—Hart
P—Pt(鉑)
正確地選用電磁流量計是保證用好電磁流量計的前提條件。選用什么種類的電磁流量計應根據被測流體介質的物理性質和化學性質來決定,使電磁流量計的通徑,流量范圍,襯里材料,電材料和輸出電流等,都能適應被測流體的性質和性質和流量的要求。
污水泥漿電磁流量計可測量的流體
由電磁流量計的工作原理可知,能選用電磁流量計測量流量的流體必須是導電的,嚴格的說,除了高溫流體之外,只要電導率大于5μ/cm的任何流體都選用相應的電磁流量計來測量流量,因此不導電的氣體,蒸汽,油類,等物質不能選用電磁流量計來測量流量。
傳感器口徑的確定
流量計使用流速在0.3-15m/s范圍內,此時流量計口徑可選擇與用戶管道口徑一致。
使用流速低于0.3m/s時在儀表部位局部提高流速,采用縮管方式:
一體型或分離型的選擇
一體型:現場環境較好的情況下,一般都選用一體型,即傳感器和轉換器組裝成一體。
分離型:即傳感器和轉換器分開裝于不同的地點,一般出現以下情況時選用分離型。
⑴環境溫度或流量計轉換器表面受輻射溫度超過60oC.
⑵管道震動較大的場合。
⑶會對傳感器的鋁殼嚴重腐蝕的場合。
⑷現場溫度較大或有腐蝕性氣體的場合。
⑸流量計裝在高空或并下調試不方便的場合。
訂貨時應注明傳感器的轉換器分離距離,一般不能超過100m,轉換器為墻掛式安裝。
電、接地環材料的選擇
應根據被測的流體的腐蝕性來選擇電的材料,請查有關腐蝕手冊,對于特殊流體應作試驗
材料 |
耐腐蝕性能 |
含鉬不銹鋼 (OCr18Ni12Mo2Ti) |
硝酸、溫室下<5%硫酸、沸騰的酸、蟻酸、堿溶液、在一定壓力下的亞硫酸、海水、醋酸 |
哈氏合金C 哈氏合金B (HC HB) |
耐氧化性酸、氧化性鹽、耐海水、耐非氧化性酸、非氧化性鹽、堿、常溫硫酸 |
鈦(Ti) |
海水、各種化物和次酸鹽、化性酸(包括發煙硝酸)、有機酸、堿 |
鉭(Ta) |
除氫酸、發煙硫酸、堿外的其余化學介質、包括沸點的。硝酸和<175oC硫酸 |
鉑(Pt) |
各種酸、堿、鹽不包括王水 |
襯里材料選擇說明
應根據被測介質的腐蝕性、磨損性和溫度來選擇內襯材料。
內襯材料 |
名稱 |
符號 |
性能 |
工作溫度 |
適用液體 |
橡膠 |
丁橡膠 |
|
耐磨性中等,耐一般低濃度的酸堿鹽的腐蝕 |
<80OC |
自來水、工業用水、海水 |
聚胺脂橡膠 |
|
的耐磨性能,耐酸堿性能較差 |
<60OC |
紙漿、礦漿等漿液 |
|
塑料 |
聚四乙烯 |
F4或PTFE |
化學性能很穩定,耐沸騰的、硫酸、王水、濃堿的腐蝕 |
<180OC |
腐蝕性強的酸堿鹽液體 |
四乙烯和六丙烯譯名:特隆FEP |
F46或FEP |
化學性能略遜于F4 |
|
腐蝕性的酸堿鹽液體 |
|
塑料 |
四乙烯和乙烯 |
F4或ETFE |
化學性能略遜于F4 |
|
腐蝕性的酸堿鹽液體 |
聚乙烯 |
PO |
化學性能穩定 |
<60OC |
污水 |
|
聚苯硫醚 |
PPS |
|
<150OC |
熱水 |
紊流)就不會影響測量結果的。因此說電磁流量計是一中真正的體積流量計。對于制造商和用戶來說,只要用普通的水實際標定后就可以測量其他任何導電流體介質的體積流量,而不需要任何修正。這是電磁流量計的一突出優點,是其他任何流量計所沒有的。測量管內無活流量范圍的選擇
流量和zui小流量必須符合下表中的數。
|
產品簡介product introduction
EMF5000系列一體式電磁流量計,適用于測量封閉管道中導電液體和漿液的體積流量,如水、污水、泥漿、紙漿、各種酸、堿、鹽溶液、食品漿液等,適用于石油、化工、電力、礦冶、給排水、輕工、食品等行業。
EMF5000 series integrated electromagnetic flowmeter, Suitable for measuring the volume flow of conducting liquid and slurry in pipeline, Such as water, sewage, slurry, pulp, all kinds of acid, alkali, salt, food slurry etc., Applicable to the petroleum, chemical, electric power, metallurgy, water supply and drainage, light industry, food industry etc..
EMF5000系列一體式電磁流量計是在流量儀表領域中多年經驗的結晶,其設計與儀表質量控制體系保證了產品的和高可靠性,EMF5000系列一體式是經過多年不斷升級改良而來的。
EMF5000 series integrated electromagnetic flowmeter is the crystallization of many years of experience in the field of flow meter, The design and appearance quality control system to ensure that the products of high precision and high reliability,
EMF5000系列一體式電磁流量計采用技術。利用恒流低頻三值矩形波或雙頻矩形波勵磁、既有矩形波磁場的優點,又克服了正弦波磁場的缺點;還可以消除電源電壓波動、電源頻率變化及勵磁線圈阻抗變化所造成的誤差;并有的零點穩定性和不受流體噪聲干擾影響。從而使產品具有高可靠性,高穩定性的特點。
EMF5000 series integrated electromagnetic flowmeter using the latest technology in the world. Using constant current of three value low-frequency square wave or dual frequency rectangular wave excitation, Has both advantages of rectangular wave magnetic field, It overcomes the shortcomings of the sine wave magnetic field; It can eliminate the power supply voltage fluctuation, Error variation of power frequency and excitation coil impedance changes caused by; Zero stability and good and is not affected by the fluid noise interference. The product has high reliability, The characteristics of high stability.
除此之外,在本產品中還把勵磁線圈設計成具有產生非均勻磁場分布的特點,從而使傳感器做成小型輕量化,可對非對稱流所產生的誤差起到一定的補償作用。
In addition, In this product the excitation coil designed with non uniform magnetic field distribution, The sensor made of all size and light weight, The error can be caused by the asymmetrical play a certain compensation.
二、產品特點product features
1、EMF5000電磁流量計結構簡單,無轉動部件,因而無摩擦,工作壽命長,計量精度高,性能可靠。
1, the EMF5000 electromagnetic flowmeter has the advantages of structure,No rotary parts, So there is no friction, Long working life, High precision measurement, Reliable performance.
2、傳感器測量管中無節流和阻流部件,因此無附加壓力損失,不存在堵塞問題,適用于測量含有懸浮物、固體顆粒、纖維等的兩相流(如泥漿、污水、礦漿、紙漿、等粘性較大的漿液)。
2, the sensor measuring tube without throttle and choke component, Therefore, no additional pressure loss, No blocking problem, Suitable for measuring the containing suspended matter, Solid particles, Two phase flow fiber etc. (such as mud, sewage, slurry, pulp, and viscosity of the slurry).
3、由于信號在整個充滿磁場的空間中形成,它是管道截面上的平均值,因此從而電平面至傳感器上游端平面間所需直管段相對較短,長度為10×D(D為管道的內直徑)。
3, because the signal is formed in the magnetic field in full space, It is the average cross section of the pipeline, Therefore thus electrode plane to the sensor upstream the end plane straight pipe section with relatively short, Length of 10 × D (D is the internal diameter of the tubes).
4、EMF5000電磁流量計無機械慣性、反應靈敏、可測量瞬時脈動流量,也可與單元組合儀表、計算機配套組成各種自動檢測、調節系統和程控系統。
4, EMF5000 electromagnetic flowmeter without the mechanical inertia,Sensitive reaction, Measurement of instantaneous flow rate pulsation, Can also be instrument and unit, Computer matching the composition of a variety of automatic detection, Control system and control system.
5、傳感器輸出信號是一個與平均流速成線形關系的電動勢,并且測量結果與液體的溫度、壓力、密度、粘度、電導率(不小于電導率)等物理參數無關,如用水標定的流量計同樣適用于其它介質的流量計量,無壓力損失無需修正。因此測量精度高、工作可靠。
5, the output signal of the sensor is an exact linear relation with the average velocity of the electromotive force, And the measurement results and the temperature of the liquid, Pressure, density, viscosity, Conductivity (not less than the minimum conductivity) independent physical parameters, Such as water flow metering flowmeter calibration is also applicable to other media, No pressure loss without correction. Therefore, high measuring precision, reliable work.
6、EMF5000電磁流量計采用四電,內置接地電,用于非導電管道無需另加接電環。
6, EMF5000 electromagnetic flowmeter with four electrodes, The built-in grounding electrode, For non conductive pipe without additional power connection ring.
7、同時帶有4~20mA電流信號輸出、脈沖輸出及瞬時流量上下限報警輸出,另外可選RS485通訊及HART協議,3.6V鋰電池供電GPRS無線遠傳輸出。
7, at the same time with a 4~20mA current signal output, Pulse output and instantaneous flow alarm output, Another optional RS485 communication and HART protocol, 3.6V lithium battery GPRS wireless remote output.
8、現場顯示瞬時流量,百分比,流速,正反向累計流量和總累計量。
8, the site displays instantaneous flow, Percentage, Velocity, Positive and negative cumulative flow and total cumulant.
9、供電方式有AC220V,DC24V,自帶3.6V鋰電池。
9, power supply AC220V, DC24V, 3.6V lithium battery.
10、轉換器支持中文版及英文版轉換設置。
10, converter supports Chinese version and English version conversion settings.
三、技術參數the technical parameters
環境溫度:-40℃~+85℃
Environmental temperature:-40℃~+85℃
相對濕度:5%~95%
Relative humidity: 5%~95%
機械振動:頻率≤55HZ振幅≤0.55mm
Mechanical vibration: Frequency≤55HZ Amplitude≤0.55mm
環境電磁場:≤400A/m
The electromagnetic field: ≤400A/m
介質溫度:≥-40℃,≤+120℃(介質溫度高于70℃建議選分體式)
Medium temperature: ≥-40℃,≤+120℃(medium temperature higher than 70 ℃ sested split)
流體電導率:被測流體電導率≥5μs/cm
Fluid conductivity: The measured fluid conductivity≥5μs/cm
測量精度:0.5%
Measurement precision: 0.5%
重復性:0.1%
Repeatability:
功耗:啟動時≤300W,正常運行≤50W(包括傳感器和轉換器)
Power waste. Boot time ≤ 300W, The normal operation of ≤ 50W(including sensors and converters)
工作電源:AC220V,DC24V,3.6V鋰電池
The working power supply: AC220V,DC24V, 3.6V lithium battery
四、工作原理work principle
EMF5000電磁流量計原理是基于法拉第電磁感應定律。流量計的測量管是一內襯緣材料的非導磁合金短管。兩只電沿管徑方向穿通管壁固定在測量管上。其電頭與襯里內表面基本齊平。勵磁線圈由雙向方波脈沖勵磁時,將在與測量管軸線垂直的方向上產生一磁通量密度為B的工作磁場。此時,如果具有一定電導率的流體流經測量管,將切割磁力線感應出電動勢E。電動勢E正比于磁通量密度B,測量管內徑D與平均流速v的乘積,電動勢E(流量信號)由電檢出并通過電纜送至轉換器。轉換器將流量信號放大處理后,可顯示流體流量,并能輸出脈沖,模擬電流等信號,用于流量的控制和調節。
EMF5000 electromagnetic flowmeter is based on Faraday's law of electromagnetic induction. Measuring tube is non magnetic alloy tube a lined with insulating material. Two electrode along the diameter direction through the tube wall is fixed on the measuring tube. The electrode head and the liner suce is substantially flush. The excitation coil is composed of a bidirectional square wave pulse excitation, In the axis perpendicular to the direction of the measuring tube and generates a magnetic flux density of magnetic field of B. At this time, If the fluid has certain conductivity through the measuring tube, Cutting the Magnetic Induction EMF E. E electromotive force is proportional to the magnetic flux density B, Product measurements of tube diameter D and average velocity v, Electric potential E (traffic signal) by electrode detection and through a cable sent to the converter. The converter will flow signal amplifying and processing, Can display the fluid flow, And can output pulse, Analog current signal, For regulating the flow of control.
五、選型圖譜the selection of